Density(g/cm3): 1.4-1.7
Water absorption(%):≤28
Wet expansion(%):≤0.25
Ignitability: Incombustibility A class
Water penetration: Allow wet trace on back without any drops of water
Flexural Strength (Mpa): Dry: ≥16.4 Saturated: ≥13.4
Frost resistance: 25 cycles under freezing and thawing, no cracks,
no layers
Radioactivity: Environmental protective A class
Asbestos: 100% free of asbestos
Thermal conductivity: 0.30(26ºC) W/ (m.K)
Drying Shrinkage: <0.1%
Free Moisture at Equilibrium Moisture Condition: <10%
The main advantages of our wooden grain fiber cement board:
1. Beautiful appearance of our wood grain fiber cement board
2. Good durability of our wood grain fiber cement board
3. Excellent fire-proof and damp-proof performance of our wood grain fiber cement board
4. Anti-cold and high temperature resistance of our wood grain fiber cement board
5. Low expansion rate, low contractibility, no shape changing.
6. Being easy to be processed and fixed
7. Environmental protection type of our wood grain fiber cement board
8. Surface can be coated and brushed
The application of the wooden grain fiber cement board:
1. Old and new building curtain walls, exterior walls and other
outdoor systems
2. European and American styles of architecture and high-end villa
roof
3. Outdoor hall, office, building facade and podium
4. Kitchen, bathroom, bathrooms, changing rooms and other damp
places
5. Subway stations, tunnels and underground works
6. Exterior wall decoration system
7. High quality requirements of the ceiling
8. Environmental requirements, particularly Germany occasions
9. Any external wall of villa can use our wood grain wall panel
Safety capability:
| Item | Index | Instruction |
| Asbestos contain | 100% asbestos free | Safe for application |
| Radioactivity | <1.0IRa | Safe for application |
| <1.0Ir | Safe for application |
| Incombustibility | A1 | The highest grade |
INSTALLATION STEPS:
1. Check to be install wall is smooth and clear wall obstructions.
2. Find out the pending installation of the wall benchmark
standards, and pending installation the wall Simiandan line mark to
prepare the keel.
3. Emissions and a fixed keel, the keel can be used 50 # light
steel keel 2.5 * 3cm wooden poles can also be used. Will keel
vertical direction by 60 cm spacing in the wall, expansion
fasteners for nails or screws. Requirements for anti corrosion
material, or embalming fluid, asphalt preservative treatment of
timber with a wooden keel; doors and windows have to be laid around
strengthening the keel.
4. Start the installation from the bottom of the first layer of peg
board (bottom), and nail or 3.5cm long self-tapping screws to hang
the board keel; Note: If you use self-tapping screws in advance
with twist drill pre-drilling and nail The plane 0.5-1mm head sink
into the external walls of three Lok grain peg board, nail head
position to be treated with preservatives and wall putty Phi flat;
board nail holes from the board along not less than 1.2cm in a
uniform 1.5cm is better ; from the two boards side 2cm.
5. Installation of a second three Lok siding lap method using the
same fixed (up and down the two hanging panels overlap to cover 2.5
cm) and so on to install other peg board. Note that when the width
of the wall over the length of the peg board, two of the same
horizontal line hanging board interfaces should be in the keel, and
shall not be vacant connection.
6. Fiber Cement Siding Board level interface to retain 35 mm
joints, according to the requirements of fixed finished, can be
coated with polyurethane glue (PU25) or tile adhesive to fill
joints; one end of the peg board and angles or exterior angle
connected to the Department should move closer to the natural, and
leave the appropriate gap with glue or tile adhesive seal;
installed on top of the last piece of peg board, peg board and the
top of the cornice junction should also adhesive seal to the
plastic or tiles to achieve a waterproof purpose.
7. Install Fiber Cement Siding Board to the door, window position,
cutting the corresponding shape with the Door, window cover shape
loft hanging board should be installed to avoid through the seam
and connected at playing silicone or with tiles binder filled, to
avoid through the slit, resulting in leakage.
8. The junction of two adjacent walls (i.e. the Yin angle and Yang
angle) Fiber Cement Siding Board in need of shut up,common approach
45 degrees chamfer patchwork and dedicated Corner shut two kinds
approach. Yin angle simply two with the level of the adjacent wall
hanging board 90 degrees perpendicular to each other fixed,
caulking seams sealed can.
9. Fiber Cement Siding Board installed after a clean brush or towel
and wipe again brushing the board of ash or oil. Acrylic exterior
paint, the paint is better, one end of both sides brushing the
surface of the peg board.
Non-fixed keel installation method:
1. Check to be to install wall is smooth and clear wall
obstructions.
2. Find out until the installation of wall benchmark standards for
the width calculation based on the peg board and pending
installation the wall Simiandan line (peg board horizontal
separation line).
3. Began installing the first piece of floor pan of water from the
foot of a wall, using the Fischer transmission Anchorage, every 50
cm peg board drilled with a drill and depth of holes drilled in the
wall, and filled into the
nylon anchor bolt and fixed the screw. Board nail holes from the
board along shall not be less than 1.2 cm, 1.5 cm in a uniform is
better; from the two boards side 2 cm.
4. The same fixed overlap method to install the second block of the
external walls of three Lok grain sandwich boards (up and down the
two hanging panels overlap to cover 2.5 cm) and so on to install
the other peg board.
